Factory Supply Iron Fire Pit Ring With Wildlife Cutouts For Backyard Patio Camping Outdoor Wood Burning Fire Pit

  • Taille du produit : coutume
  • Couleur:noir, couleurs personnalisées acceptées
  • MOQ :Ensemble de 100
  • Matériel:Métal-fer
  • Délai de livraison des échantillons :7 à 15 jours (selon le nombre d'échantillons)
  • Délai de livraison :30 à 45 jours (selon le nombre de commandes)
  • OEM/Personnalisation :On peut s'y référer à l'aide d'images ou d'échantillons.
  • Lieu d'origine :Fujian, Chine
  • Importation et exportation :Port de Xiamen, Fujian, Chine
  • Paiement:L/C,T/T

Présentation du produit

A fire pit ring is the fire without the bowl. Instead of a vessel standing on legs, this is a band of metal-iron that keeps the burning logs together on the ground where the fire is meant to be — the centre of a patio, a gap in the planting, the inside of an existing stone surround, or bare earth at a campsite. There is no base to collect rainwater and no lid to lift off, which is why a ring suits a fire that is lit casually and left to burn down rather than tended all evening.

The format also solves a merchandising problem. A bowl looks like a bowl in any photograph; a ring is a continuous wall, so a pattern runs all the way around it and the piece has a front, a back and a story. That makes it a natural addition to a range that already carries plain bowls, supports à bois de chauffage and tool sets, where one motif-led item changes how the whole group reads on a listing or on a sales floor.

Most of the buyers we work with as an iron fire pit ring supplier are putting a seasonal range together rather than buying a single unit: a distributor filling a spring outdoor-living plan, a garden-centre buyer wanting one decorative piece beside the plain bowls, or a private-label brand developing its own custom iron fire pit ring under its own label. Each of them is judging the same two things — whether the artwork holds up, and whether the finish will survive a season outdoors.

 

Caractéristiques principales

  • Heat-resistant black coating. The standard colour is black, applied over cleaned iron and built for the repeated heat cycles of a wood fire rather than a single season of use.
  • Open top, no base. There is nothing to lift off before lighting and nothing to tip out afterwards; ash is raked or shovelled away once the ring is cold.
  • A wall that holds the log bed. Logs stack against the inside face and burn in a contained bed instead of collapsing outward, which is what makes a ring easier to feed through an evening than a shallow bowl.
  • Compact to pack. A ring takes less carton volume than a bowl of the same diameter, so it mixes well with bowls, racks and tool sets in a mixed container.
  • No front and no back. The motif is carried around the wall rather than on one face, so a custom wildlife cutout fire ring reads the same from every seat around the fire.

Restons en contact

Écrivez-nous, envoyez-nous un courriel ou mieux encore, venez nous dire bonjour !

Nom

salle d'exposition decentcrafts

Certificat d'artisanat décent de Fujian Quanzhou

Caractéristiques techniques

Property Détails
Type de produit Wood-burning fire pit ring
Taille 36 x 12 in standard; custom sizes reviewed per order
Motif Wildlife cutouts through the ring wall
Matériel Métal-fer
Couleur Black; custom colours accepted
Terminer Heat-resistant coating
Construction Open ring wall, no base and no lid
Lieu d'origine Fujian, Chine
Customization Referred from pictures or a physical sample

 

 

Wildlife Cutouts & Edge Finishing

The wildlife pattern is the reason this ring gets picked up, so it is worth knowing how it is made. The animals are openings cut straight through the iron wall — not a print, an etch or a plate fixed on top. In daylight the ring reads as a band of silhouettes; with a fire inside, the openings become windows and the pattern is thrown onto the ground and the stone around it.

Cut quality is what separates a finished piece from a punched one. After cutting, the edge of every opening is dressed back so no burr is left to catch a finger, a sleeve or a poker. Run a thumb around one silhouette on the approved piece and the edge should feel turned over rather than sharp; that is the check we expect a buyer to make before a production run is booked.

Consistency is harder than any single cut, and it is where an iron fire pit ring supplier earns a repeat order. One approved ring becomes the reference: the same artwork, the same scale, the same spacing around the circumference, the same coating over the top. Forty rings standing open on a shop floor show up small shifts immediately, so artwork is signed off before the first run and checked back against that reference afterwards.

Scale is worth settling early with your sales contact. A motif that reads well from a patio chair is not the same as one designed for a close-up product shot, and a mark with thin legs, antlers or fine foliage needs more open space around it than a solid shape. Send the artwork or reference image you have in mind for your custom wildlife cutout fire ring and we will tell you what holds up once it is cut.

 

Processus de personnalisation

  1. Send the reference. A photograph, a drawing or a physical sample is enough to start, and the closer it is to what you want, the quicker the review.
  2. Review what can change. Diameter, wall height, colour, motif and pattern spacing for your custom iron fire pit ring are all looked at against that reference; some changes are simple adjustments, others need new tooling, and we say which is which before you commit.
  3. Approve the first ring. The piece you sign off becomes the standard — artwork, scale, spacing, colour and edge finish.
  4. Lock the specification. Artwork, colour reference and any branding or packing detail you need are written down and agreed; a change after that point is reviewed again because it can affect timing and cost.
  5. Check before packing. Rings are inspected against the approved piece for dimensions, motif alignment, edge finish and coating coverage before they are packed for dispatch.

 

Fitting & Placement

  • On open ground. Set the ring on bare soil, gravel or a stone pad and clear grass, roots and leaf litter from around it; the ring defines the burn area and the ground does the rest.
  • Inside an existing surround. Dropped into a brick or stone pit, the ring takes the flame and the ash directly and keeps the masonry behind it cleaner.
  • On a patio. Give it a non-combustible base — paving slabs or a stone plinth — and keep it off timber decking, artificial turf and dry grass.
  • At a campsite. A ring packs flat, travels in a vehicle and gives a fire a defined edge on bare ground; check the site’s own fire rules before lighting it.
  • Repeat units on a terrace. Hotels, pubs and event venues often run several along a terrace, so plan the run as a set rather than as single pieces.
  • Wholesale display. Standing open at eye level, a custom wildlife cutout fire ring shows the whole pattern front-on and presents the range beside the plain bowls.

 

Utilisation et entretien

  1. Let it cool completely. Iron stays hot long after the flames die, so never lift or move the ring while there is heat in it.
  2. Empty the ash cold. Scoop or tip it into a metal container; a thin layer left inside is fine as a bed for the next fire.
  3. Clean dry first. A soft brush or dry cloth removes most soot; for sticky marks use a damp cloth with a little mild detergent, then dry the surface straight away.
  4. Keep abrasives away. No wire wool, scouring pads, strong acids, alkaline cleaners or pressure washing — they strip the coating and give rust somewhere to start.
  5. Touch up chips. Clean and dry the area, then apply a heat-resistant metal paint matched to the black finish; ask us for the finish reference if you need one.
  6. Store it out of the weather. A dry, ventilated shelter is preferable; outdoors, use a breathable cover so condensation can escape. Coastal air and standing water are the hardest conditions for any iron fire feature, so check the ring more often there.

 

Commandes et livraisons

Property Détails
Commande minimale 100 ensembles
Délai de livraison indicatif 7-15 days, depending on the number of samples
Production lead time 30-45 days, depending on the number of orders
Payment Lettre de crédit, virement bancaire
Export port Port of Xiamen, Fujian, China
Shipping terms Confirmed on the proforma invoice
Packing details Confirmed once the product and carton design are approved

 

 

Chaîne logistique et garantie de livraison

Decent Crafts has been sourcing and exporting from Quanzhou, Fujian since 2008, and goods leave through the port of Xiamen. We work with a network of metal-working suppliers across the region, so a mixed order — several categories, colours or sizes — can be consolidated into one shipment with a single set of export documents. Sampling normally runs 7–15 days and bulk production 30–45 days, booked ahead of peak season; we inspect before packing and can bring in a third-party inspector. Payment is by T/T or L/C, with final terms and Incoterms confirmed on the proforma invoice.

 

FAQ

Q1. Is a fire pit ring a complete fire pit, or does it need something under it?

It is the wall of the fire, not a bowl with a base. The ring stands on a non-combustible surface — bare soil, gravel, paving slabs or a stone pad — and that surface does the job a bowl base would. On a patio, set it on slabs or a plinth rather than directly on timber decking, artificial turf or dry grass.

Q2. How do I know the 36 x 12 in ring will suit the space I have?

Measure the burn area and the walking space around it before choosing. 36 x 12 in gives a footprint that suits a backyard or a generous patio; a small courtyard, or a tight fit against a wall, is usually the point at which to discuss a custom diameter. Leave enough room for chairs to pull back without anyone stepping over the rim.

Q3. Can the wildlife motif be changed to another animal, a landscape or our own logo?

Yes. Artwork for a custom iron fire pit ring is reviewed from a picture, a drawing or a physical sample, and the approval step is where you see it cut. Marks with thin legs, antlers or fine foliage need more open space around them than solid shapes, so send the artwork early and we will tell you what holds up.

Q4. Will the cut openings feel sharp when someone brushes against the ring?

Each opening is dressed back before coating, so the rim of the motif feels turned over rather than sharp. Check one silhouette with your thumb on the approved piece — that edge is what every production run is matched against.

Q5. How does the black finish hold up, and can it be repaired?

The finish is a heat-resistant black coating built for repeated wood fires and ordinary outdoor weather. Heat, weather and abrasion eventually mark any iron fire feature; when the coating chips, clean and dry the spot and touch it in with a heat-resistant metal paint matched to the black, then keep the ring covered or under shelter between seasons.

Q6. What should I burn in it?

Dry, seasoned hardwood gives the steadiest fire and the least smoke. Green or wet wood spits and smoulders, and painted, treated or glued timber — plywood, pallets of unknown treatment, household waste — should stay out of any fire pit. Follow local rules on open fires and check the site before lighting.

Q7. How do you keep the motif and finish consistent from one order to the next?

The first approved ring stays the reference. Artwork, scale, spacing, colour and edge finish are all recorded against it, and each run is checked back against that piece before packing — the practical way an iron fire pit ring supplier keeps a range looking like one range.

Horloge

noir, couleurs personnalisées acceptées

Taille

36 x 12 pouces